Corsa C Z22SE fitting Guide

#41
i find parts at breakers or on here when someone breaks a car, or use genuine parts from LMF, Autovaux or Vauxhall dealer.
be sure the chains have been done before you fit the engine as its engine out to do them in the corsa :(
 
#42
i find parts at breakers or on here when someone breaks a car, or use genuine parts from LMF, Autovaux or Vauxhall dealer.
be sure the chains have been done before you fit the engine as its engine out to do them in the corsa :(
 
#44
Its just swapping the trigger wire from earth to live or the other way under the fuse board.
Cut the wire and either run a constant earth for a live switched or an ignition switched live for an earth switched.
 
#47
On modifying a loom now to run Z22se but about 4-5 of my pins don’t match what your diagram says
Mine seems to only have one wire for immobiliser
No solid red in pin 17
Pin 18 witch is meant to be red was blue with a red tracer
And I can’t remeber the other ones that were different
Have you ever had this before?
 
#50
Z12XE and Z12XEP are different, maybe that's what you have?
When i did mine the pins were different on the z12xe to the z22se, as in a different type of pin so they did not fit the z22se plug body.
all Corsa C petrols do have 2 wires which connect to the immobiliser though.
 
#54
Wondered if anyone knows what pin on the ecu the service indicator to the clocks is by any chance as i've not been able to find any pinouts showing this. Cheers Liam
Service indicator?
do you mean the INSP that displays on the trip mileage display after start up? If so that is done thought the canbus on the Corsa C.
 
#55
Its the spanner light that flashes on the dash on an astra g to tell you that you need a service ect but i cant reset it via the correct way so i want to find out what pin from the ecu feeds the light if that makes sense cheers
 
#56
that's the EML light you need to read the codes, fix the fault then you can clear it.
Vauxhall's have 2 EML lights, engine with spanner is usually down to an emissions fault and the engine with the electric flash is engine electrical faults. both will store codes
 
#59
Update with wiring for the Z12XEP and Z14XEP.

Corsa C Z12XEP/Z14XEP to VX220 Z22SE
Z12/14XEP Z22SE
Pin No Wire Colour Function and Pin No Wire Colour Pin No
4 Red/White Throttle Pedal 1 Black 64
5 Brown/white Throttle Pedal 5 Green 21
21 Red/Blue Throttle Pedal 2 White 31
22 Brown/Blue Throttle Pedal 4 Yellow 53
37 White/Green Throttle Pedal 6 Brown 61
54 white/Yellow Throttle Pedal 3 Blue 49
11 Green Canbus not present but use this Green 11
43 White Canbus not present but use this White 27
2 Brown/Violet Immobilizer 7 Brown/White 59
29 Brown/Blue Immobilizer 2 Brown/Blue 63
59 Blue/Red Vehicle Speed Signal Yellow/Grey 18
20 Green Tacho/EPS White/Black 9
14 Brown/Red Engine Cooling K30A Relay Blue/Grey 13
33+49 Red/Black Engine Control K26 Relay 12V Power Green 19
19 Brown/Black Engine Control K26 Relay earth switch Green/Pink 30
18 Red Constant 12V supply Violet 20
46 Brown/Red Fuel Pump K35 Relay (needs to be swapped to live switch) White/Violet 29

X18 plug six pin supply plug to engine X39 plug
1 Blue/Green Oil Pressure switch/lamp Blue/Green 2
3 Red/Black Injectors (needs dividing off engine side) Red/Blue 5/spare
5 Black Coil pack (needs dividing off engine side) Red/Blue 5/spare
Alternator trigger Blue/White spare

  • Starter trigger Black/Red spare
 
Top