Search results for query: *

hello guys. my vectra c z22se come up with p0171 periodic most times it come up if im holding for red light or like that then it can be there for a couple of days and be gone by it self again but i dont really feel any changes in the way the engine is running. sometimes it takes a long time...

Hello guys. I have Been thinking about changing my electric intake/fuel system with 4 motor cykel caburator on my z22se engine but my big question is how do i do with the ecu. I think there Will be some trouble with air flow sensor and Lambada since that Will have to disconnected and that Will...

hello guys. i lowered my vectra c 2.2 45mm when i bought it but now a year later the brand new tires are worn badly on the inside on the rear. can i get something or do something to adjust the rear camber more than the standard adjustment allows me to. i cant seem to find anyting. the car is...

hello clever guys. i finally recieved my op-com and i figured i would activate my cruise control since everything else should be ready for it. before i did so my egr is broke. well i activated it and it didnt work BUT now my car doesent show my speed. it stays at 1500-1700 rpm in idle at all...

Okay as some of you have read in a previous post i am rebuilding a z22se for my car. I figurer i would make a New post for Help and pictures for other if some in the future can use it. And og i need Help to have it all at One place. First off my plans. Balance shaft remove. Rebuild with all...

hello guys. i have a z22se engine im looking to rebuild all original but i cant seem to find the part numbers. so if anyone have the part numbers for original crank bearing and rod bearings any curious where do u find the part numbers ? would you change the lower bolts used to assemble the 2...

hey guys im looking for a good performance manifold for my vectra c z22se a dbilas or 4 brand or something other that is good :D and i am from denmark so you have to be willing to send it here i will ofcourse pay postage

hello guys im starting to upgrade my z22se. i have so far portet the new head and de-restricted airbox. i have seached the web for hours to find a good performance exhaust manifold for my engine and i havent manage to find even 1 in stainless stel but the only one ive found is a cast iron...

hello guys. i have an annoying knocking sound in the rear i am pretty sure it,s a bush from reading different forums. BUT i cant figure out witch one since there apparently are lots of different names for the different arms. any chance someone have a picture of the most common bush on the car en...

finally my car runs good so back to the fun part :D im starting to build a stainless steel system i plant to make the manifold from 1.5'' and into to 2.5'' but i cant seem to figure out if i shall make the manifold short and put the cat against the engine as the original or make it long and...

Hello As some of you have seen in earlyer threads ive done alot of work on my car. With the clutch change i desided to change box oil and my local shop told me to buy 2 liters of GL3+ 75-80 but now the changes are extremely bad And the old oil was red wich by my knowledge is automatic...

hello ppl i have had a bunch of problems with me vectra as some of u have help me with i,ve take off the gearbox to look at the clutch and flywheel and yes its bad it is blue/yellow all over from heat i think it is crucked and way to much slip on it so new flywheel for sure the clutch plate as...

hey guys :) i was so unlucky my new baught vectra c z22se jumped the chain before i got to replace it. well it damage all intake valves. but i found a complete dissasembled z22se engine extremely cheap witch i took the cylinder head from and put on my engine before install i had it pressure...

hello guys i am brand new to this forum a guy recommended me to join here for my z22se questions so thanks for the membership :D I've recently got a vectra c 2.2 z22se i want more power out of it its boring since im used to drive an old bmw e32 750 with 450+ so i need a bit more out of this one...