Search results for query: *

  1. N

    Two 312 profile CAMS on Z22SE, did test someone?

    Hi friends, while im waiting for my 312/257 CAMS i would like to test run a new built engine. Old cams failed on bearings (low on oil), but i have here two good 312 s. Did someone tested this setup to start and run the engine?
  2. N

    Z22SE Z22se swap z22yh

    Was before Z22SE bottom installed in the car? If yes search for Z22SE trigger wheel. They are different in SE/YH. But if you had previously a Z22YH bottom and head then you will also need new ECU. And maybe more things (dont know if it has also low pressure fuel pump etc...)
  3. N

    Reluctor ring position on Z16XER

    Hi, yes, when cyl 1 + 4 are on TDC, the index pin on the ring is also on top just a little bit right. Exactly like on the TIS drawing. On your images the reluctor is still installed. Its seen on the holes. Btw. did you hear some bad words on these engines? Looks like the one i swapped the...
  4. N

    Reluctor ring position on Z16XER

    yes, its Z16XER, its located under the flywheel, A16XER have it internal, but i found out the right placement, on first sight it seemed that it could be placed evers 180deg, but the flywheel bolt pattern is unsymetrical, so there is definitively only one position to fit. I found some image of...
  5. N

    Reluctor ring position on Z16XER

    Hi friends, this is a little bit off topic, but i needed to change flywheel on Z16XER with damaged starter toothing, and this engine has the reluctor ring under the flywheel near the crankshaft seal. I tought that it will only have one position to install, but it can be installed every 180deg...
  6. N

    Vectra C Z22SE main berings

    Theyre so expensive??? I doublechecked them yes they are STD.
  7. N

    Vectra C Z22SE main berings

    Hi vocky, thanks for your reply. I tought thatt the 1.8 was a real 1.8 (never had one exact), but seems like my troubles regarding this engine build never stop. I sucessfully ordered a set of genuine 12591092 STDs. But i was a bit disappointed that theres no STD marking on them. I must check...
  8. N

    Vectra C Z22SE main berings

    Are the saab B207 ones from 1.8/2.0T also the same?
  9. N

    Vectra C Z22SE main berings

    Hi friends, im rebuilding now a Z22YH engine. Im searching in my country for GM90537821 Gm90537330 main bearings but i cant find them. Also i looked up King bearings MB5413SI, but also they are unavaible here. Does anybody know PNs, if they exist, of more aftermarket companies producing a good...
  10. N

    Z22YH Z22YH crankshaft diameter/bearing tolerances

    Hi, that comparison table is great. The thing about other trigger wheel is well known. Some time ago i swapped on my car the SE for an YH and, i wanted to rebuild the SE but the car drives to this day great. I also posted here on forum an universally adjustable triggerblade for the crank...
  11. N

    Ceramic cluth flywheel

    Hi friends, i am using a DIY ceramic clutch assembly with original modified flywheel and stock pressure plate on one engine. (Its not Z22 or derivate, :-) forgive for a other engine) but i want to make my own flywheel. I hope someone here already had done this kind of mod. Now the question is...
  12. N

    Z22YH Z22YH crankshaft diameter/bearing tolerances

    Thank you. It helped a lot. Are these information available in TIS also?
  13. N

    Z22YH Z22YH crankshaft diameter/bearing tolerances

    Hi, i would be rebuilding an Z22YH engine very soon, so i want to know if the same clearances of and dimensions for crankshaft main/bigend bearings apply to both Y22YH and SE or has the YH other dimensions and wear clearances?
  14. N

    Z20net water pressure

    That was my first though, that the new one is crap. Lets see what quality will be the next ill buy tomorrow.
  15. N

    Z20net water pressure

    Hi everybody, does someone know the nominal water pressure for Z20NET water system? My old pressure cap failed. (Stayed stuck in the tank so ive had to crack it to gain access to water fillup) Ive ordered new one but this one has a weaker spring. On the caps there isnt any Part.No nor pressure...
  16. N

    Vectra C Power steering pump

    Hi everybody, i just swapped the pumps. Everything works ok after proper variant coding and CAN programming. So if everyone encounter a failed pump the black connectors (equipeed with fluid level sensor) and white connector (without level sensor) can be swapped.
  17. N

    Vectra C Power steering pump

    It is this type: It has faulty oil temperature sensor. It works for about 1minute and then goes off with DTC Oil temperature too high, but the oil is still cold. So i think it will the pump. Fuses seems to be OK. (Did you mean the High power pump for the motor, or the lower fuse for the control...
  18. N

    Vectra C Power steering pump

    Hi everybody. On my Vec C Z22SE/AT5 the power steering pump has stopped working. There is a unit with rectangular shaped oil tank and white connectors. I have a spare pump, wich is fully woking, also has the rectangular shaped oil tank but the connectors are black. Could this pump be swapped...
  19. N

    Z22SE head on YH block

    Hi. After a day of experimenting everything is working great. After my tests it triggers on the iron to air edge. Wheel was placed ok, but my new sensor from the donor engine was bad. I replaced it and everything works great. Now i can repair my old engine, while still driving the car.
  20. N

    Z22SE head on YH block

    Thanks. Good to know, that the VR sensor is so sensitive. I placed the trigger wheel on the high spots of the pulleys. So now it is about 4mm spaced. Today i will test it. The sensor is about 3mm away from the trigger wheel is this good or should i go a little closer? BTW: Is the ECU triggering...
Top